LF-001 Conical Spray Valve
Linear, Single Filament & Atomization Modes
LF-001 provides linear, single filament and atomization operation modes, which are very suitable for point coating, wide pattern and thin structure applications.
Product Characteristics
Three versatile operation modes for various coating applications
Linear Mode
Material flow is applied to areas on board that are very uncoated or forbidden, or additional materials are required. To protect the location of high impedance region. Linear coating can also be used as a single coating for a single test point or component.
Single Filament Mode
The single filament type is very suitable for distributing the width of the pattern, and can maintain good edge sharpness. At the same time, shorten the cycle time. Point instructions available.
Atomization Mode
The mode is very suitable for applications requiring medium selective coatings and film construction. Spraying can be done in the range of 30-3500 mPa/s viscosity. Material, single coating width 5-10.
Why Choose LF-001
Multi-mode versatility for diverse coating needs
Multi-Mode Operation
Three operation modes in one valve: Linear, Single Filament and Atomization
Wide Viscosity Range
Handle fluids from 30 to 3500 mPa/s with precision and consistency
Sharp Edge Quality
Maintain good edge sharpness while shortening cycle time
Suitable Applications
Ready for Multi-Mode Spray Coating?
Contact our experts for customized solutions and technical support
Coating Valve Solutions
Professional valves for precision coating and dispensing applications
G-300HP High Pressure Valve
G-300HP is a rubber valve suitable for dispensing and filling of medium and high viscosity fluids. The unique structure design of stainless steel balance shaft ensures the stability of dispensing under high pressure.
Product Characteristics:
- Adjustable Backdraft and controllable glue content
- Breaks off glue cleanly
- All stainless steel structure
- Double air circuit design
- Simple maintenance
Suitable for Fluids:
Lubricating grease Grease RTV silica gel Epoxy resin Brazing paste
G-500HP Diaphragm Valve
G-500P is a micro-dispensing valve suitable for medium and low viscosity range. The diaphragm is made of strong Teflon material (PTFE), which completely separates the fluid tank from the starting parts. It has good chemical inertia, wear resistance, impact resistance and corrosion resistance.
Product Characteristics:
- Strong chemical inertia
- Handle many special materials
- Glue clean
- Simple maintenance
Suitable for Fluids:
Instant adhesive Anaerobic adhesive Medical reagent Special chemical materials
BF-028 Film Spray Valve
The BF-028 film spray valve will directly coat the coating into a fan-shaped film, which is a non-atomized film. It solves the problems of atomization, drift and flocculation of quick-drying glue, and is suitable for the application of surface coating materials with viscosity less than 100 cm.
Product Characteristics:
- Accurate edge location through accurate and selective material applications
- Maximum coating speed and multi-function to effectively increase production
- Variable Mode Width Provides Choice Diversity
Suitable for Fluids:
Quick-drying glue Surface coating materials Low viscosity fluids
SF-073 Sector Spray Valve
The SF-073 fan spray valve adds the forming gas path on the basis of the LF-001 conical spray valve. The taper is shaped into a fan, so that the efficiency of large area coating is higher. Suitable for spraying multi-state fluids.
Product Characteristics:
- Outstanding needle design, truly zero residue
- Easy to clean, no need to dismantle solvent coating
- Thickness can be up to 100-200 microns
- Single coating width: 15-30 mm
- Sprayable in the Viscosity Range of 30-3500 mpa/s
Suitable for Fluids:
Acrylic acid Silicone Epoxy UV glue
G-420A Precision Striker Valve
G-420A is a micro-dispensing valve suitable for low viscosity fluids. It can obtain very small and high consistency dispensing through stroke adjustment.
Product Characteristics:
- Disposable small size dispensing up to 0.18mm
- Not affected by bubbles in fluids
- Flow adjustable
- No residual Glue in Rubber Valve
- Glue clean, Simple maintenance
Suitable for Fluids:
UV glue Ink reagent Solvent Silicone Oil Adhesive
LF-001 Conical Spray Valve
LF-001 provides linear, single filament and atomization operation modes, which are very suitable for point coating, wide pattern and thin structure applications.
Product Characteristics:
- Linear: Material flow is applied to areas on board that are very uncoated or forbidden
- To protect the location of high impedance region
- Point instructions
- Single filament: Very suitable for distributing the width of the pattern